Underfloor Heating FAQ's
Underfloor Heating Mats
These two types of underfloor heating differ in a number of ways, each providing their own benefits.
Heating mats:
The cable used for heating mats is the same as that provided in the loose kits, with the rating of 3mm loose heating cabling being 10w/m2. The cable is already spaced and attached to the adhesive mesh backing for you, and is available in three wattages.
The most powerful heating mat is the 200w/m2, suitable for use beneath stone or tiled floors. Areas that experience a high heat loss, like a conservatory, will benefit from this type of heating mat. If you aren’t using insulation boards and laying the heating mats onto concrete, this variant should be used. A mat measuring 18m2 is the maximum that can be used with one thermostat.
A mid-range powered heating mat is the 150w/m2. Suitable for most applications, this type of solution can be used as the main heating source beneath most types of surfaces. If you are using flooring that has a finish, like Amtico or Kardean, the maximum output is 150w/m2. The largest mat size to be used with one thermostat is 24m2.
The lowest powered mat is the 100w/m2, which is suitable as a secondary heat source to take the chill off a cold floor. The largest mat size that can be used with one thermostat is 30m2.
To use with a finished subfloor like plywood or a concrete screed, we recommend that heating mats are covered in an adaptable levelling compound or a flexible tile adhesive, if you are laying tiles.
Heating cable:
Heating cable is supplied loose on a drum, so that you can manually measure and space it. The kit has full instructions for this. The cable is the same as that used in heating mats, and has a rating of 10w per linear metre.
The mats have a width of 500mm and are supplied in various lengths. To cover a room that is 4m2, you would use a roll of 8m in length and 500mm width. First, roll the mat out and cut at the end of the room. Then, flip the roll over and come back the other way.
The heating cables have a thickness of 2mm and the tile adhesive will be 5mm. You should also allow for the insulation board and tile, if used.
To heat a well-insulated, standard size room, you need a minimum of 150 watts. However, for a room that has a high level of heat loss or a lot of fixed furniture, like the kitchen, a minimum of 200 watts is recommended. If your electrical supply permits, it is recommended that you use the 200w, as this solution heats up much faster than the 150w. However, the lower power unit is the maximum wattage for use with a vinyl floor.
There are a number of factors that could affect the heat levels in a space, like insulation and the room height. However, if you insulate a space to the current regulations and use ProWarm™ tile backer boards, the system will heat the room sufficiently.
Using underfloor solutions with insulation boards will always improve efficiency, as minimal heat will be lost downwards. If you don’t have sufficient floor height to install backer boards, use thermal paint by ProWarm™ instead.
Up to 3,600w can be switched by our range of thermostats. As long as the total load doesn’t exceed this, any combination of cables or mats can be used. If a larger area is to be switched with one thermostat, use a contactor to control the load. Contact us for more details about this.
If you are connecting more than two cables or heating mats into a thermostat, you may find it difficult to get all of the fixtures into the terminals of the unit. If this is the case, use a junction box that has been positioned behind a blanking plate on the wall to connect them.
As long as the floor sensor and thermostat have been correctly installed, a temperature of around 28°C will be reached, which is not too hot to touch.
To avoid cold spots in the room, aim to cover between 80% and 95% of the free floor space. Measure the area that you intend to heat and subtract 10%, so that you don’t order too much.
Underwood Heating
Bewarm™ underwood flooring heating mats are suitable for use with engineered and laminated surfaces, as well as some types of floated solid wood floors, although you should always check with the flooring manufacturer first.
For it to work, the surfaces should be floated rather than glued or nailed down. If you are fitting tongue and groove flooring, which doesn’t click together, glue the joints, although check with the manufacturer first. The aluminium heating mats should also not be covered with any type of levelling or adhesive compounds, but hopefully the following will help if you have any further questions:
You should check with the supplier, although most manufacturers have approved their flooring products for use with underfloor heating.
If the underwood system produced by ProWarm™ is to be the main source of heating, we recommend our 10mm XPS premium insulation boards. However, if the solution is to be a secondary heating source, you will be able to fit our XPS standard insulation boards.
As long as you follow the installation guide that is provided with items, the underwood heating systems produced by ProWarm™ are suitable for areas that are likely to be wet, and fully compliant with 17th edition standards.
The heating mats for use with underwood are rated as 140w for every square metre.
All of the mats have a width of 500mm and are available in pre-set lengths between 1m2 and 12m2. For instance, an area of 10m2 would require a mat measuring 20m in length with a 0.5m width. It is possible to turn the mats to cover most floor areas, although please avoid cutting the cables.
Most free standing furniture is fine to use with heating mats, although its use under fixed items, like fitted wardrobes or units, is not recommended. To avoid any localised hot spots, we do not recommend use beneath thick rugs, insulated dog beds or bean bags.
Two mats may be connected to any ProWarm™ thermostats. Any more than this will require a junction box.
Use the aluminium foil tape supplied with the mats to join any that have been cut. This will guarantee earth continuity.
A maximum thickness of 18mm is recommended to maximise the benefits from the heating solution.
The maximum increase in floor height will be 8mm, if using XPS insulation boards by ProWarm™.
The mats may be trimmed when fitting, although the cables should never be severed.